Retrieve addresses from stock firmware

How Do I Setup Mac Address For Roomba Vacuum
How Do I Setup Mac Address For Roomba 2
How Do I Setup Mac Address For Roomba Battery

It’s a endless circle of I cant get to my settings without setting up a network, and I can’t get on my network without my MAC address. Why xbox doesn’t have a way to view your MAC address from before having to set up your network beats me. Sony doesn’t present you with this problem, you don’t have to set up a network right away. Select On if you have MAC address filtering enabled on your router. Continue the setup flow until you're presented with the MAC address. Go to your router's administrator screen and add Roomba to your approved devices list. How well did this answer your question? Locating the MAC address during Chromecast setup From the 'Connect to Wi-Fi' screen of the setup process, tap More located in the top right corner. Tap Show MAC Address.

The first step is to find out which addresses are present in stock configuration.The procedure depends on your level of access to the device's firmware.

Once you've obtained the address, click the link below to register: Register your Device Here Insignia To locate your Insignia Smart TV wired MAC address you will have to navigate to the Network settings. To navigate to the Network Settings follow these instructions Press ENTER. The settings menu opens. (or press Menu) Press or to highlight Network.
Change the rule of your router temporarily to let any device connect in, record the MAC address when Netvue camera connected and then change the rule back. Connect the Netvue camera to another router without MAC limit, record MAC address and then connect back to your router.

The result would be a list like the following:

Find out about flash locations

If you already have OpenWrt running on the device, you can try to find out about MAC locations on flash (note that not all devices store addresses there).

List partitions:

You would normally expect WiFi MAC addresses in the art partition. To check for that, use hexdump on the corresponding mtd4:

This will dump the whole partition to your console. Now you can look for addresses there: Take one byte of the vendor part of the address (first three bytes) and do text search …

The same should be done for other partitions. Usual suspects are:

If you are successful, you will have a list of addresses and locations, e.g.

You can check your data by using OpenWrt's get_mac_binary command (based on mtdX):

or by using mtd_get_mac_binary (based on partition label):

Merge your data

Now, combine data from stock firmware and your research to have a complete list:

You could also include this list in your commit message to preserve the information.

As in the example, it is possible that the same address is present in different locations. In this case, use the location that “belongs” to the interface, i.e. art for WiFi, others for ethernet.

Set MAC addresses

MAC address pulled by driver

In several cases, the MAC address is already provided at the correct location for the driver to use it automatically.

(This list is incomplete. Please extend it.)

Known cases:

ath79: mtd-cal-data: The MAC address will be read from start +2
ramips: mediatek,mtd-eeprom/ralink,mtd-eeprom: The MAC address will be read from start +4
ath10k: offset + 6

So, if you have MAC location matching those, you do not have to specify the MAC address in DTS or base-files for the particular interface.

Correct:

Suboptimal (not precisely wrong):

This can also be exploited for setting the label MAC address (see below) via 02_network.

Label MAC address

refs:https://github.com/openwrt/openwrt/pull/2159https://github.com/openwrt/openwrt/pull/2253

Many devices bear a label with one or several MAC addresses on it. Those may be used to identify the device in the network and thus represent a valuable additional information about the device.

When adding device support, you should also check which of the interface addresses corresponds to address on the label. If we assume the label MAC address ends with 0a, we could assign either LAN or 5 GHz to it. The choice for an ambiguous address is arbitrary, so let's choose 5 GHz.

There are two options to specify the label MAC address in OpenWrt:

label-mac-device DTS file

We can refer to the device bearing the label MAC address in DTS. For that purpose, one needs to reference the node with an alias, e.g.

Obviously, this is only valid if the 5 GHz Wifi device tree node actually has been named wifi0.

Attention: Not all interface can be referenced this way. To check whether there actually is a usable MAC address, check the device tree on your router:

Run

on your device.

Attention: This will only work if you have already set up MAC addresses correctly based on the information retrieved above.

It will give you a list like the following:

For each of the returned paths (if there are any), retrieve the mac-address, e.g.

Valid choices are only mac-address or local-mac-address. There may be one, two or no paths giving the correct address.

If you find the label MAC address here, check your DTS for the corresponding parent node. The correct node for /proc/device-tree/ahb/apb/wmac@18100000/mac-address would be /ahb/apb/wmac@18100000. Use this node's alias or add a reasonable one yourself if missing.

Attention: Note that label MAC addresses are assigned relatively randomly by vendors, so label-mac-device should be regularly put into DTS files or DTSIs with few users, so it is not inherited by accident.

Set label MAC address via 02_network

If device tree does not lead to the relevant MAC address, we can still set it in 02_network. In this case, you need to set label_mac in a similar way as it is already used for lan_mac and wan_mac, e.g.

This is evaluated below by the line

If possible, setting the address with the DTS approach is preferred.

How Do I Setup Mac Address For Roomba Vacuum

Using the label MAC address

When everything is set up correctly, the label MAC address can be accessed with:

Common MAC address locations

If there is an ART partition, WiFi MAC addresses are frequently/typically stored there.

ath79:

All TP-LINK routers using old tp-link header (those using Device/tplink-Xm or Device/tplink-Xmlzma templates defined in target/linux/ath79/image/common-tplink.mk), store only one mac address in <&uboot 0x1fc00>, which is the label mac address.

ramips:For ramips, typical locations for ethernet addresses are as follows:

mt7621: lan mac is at factory 0xe000 and wan mac at factory 0xe006. This is the default location for mt7621 boards in MTK's SDK.
For mt7620/mt76x8 boards if there's a lan mac at 0x28 there may be a wan mac at 0x2e. (There's only one GMAC for these two chips so GMAC2_OFFSET defined above isn't used.)

Attention: Those are typical addresses. Some vendors mix them, invert them, or even use completely different locations!

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies

The roomba integration allows you to control your iRobot Roomba vacuum or iRobot Braava m-series mop.

This platform has been tested and is confirmed to be working with the iRobot Roomba s9+, Roomba 980, Roomba 960, Roomba 890, and Braava jet m6 models, but should also work fine with any Wi-Fi enabled Roomba or Braava like the 690.

Configuration

To add your Roomba to your installation, go to Configuration >> Integrations in the UI, click the button with + sign and from